How many deck boards for a 10×10 deck?
With 5 1/2″ boards and a 3/16″ gap, a 10 × 10 ft deck takes 22 rows — 11 boards of 20′, 12 with 10% waste. Change the board, gap or framing below.
Deck size & framing
Decking
Railing
The IRC requires that a 4″ (102 mm) sphere cannot pass through a guard; a 3 1/2″ target leaves room for shrinkage. Other countries use different limits — check yours.
Span check (reference table)
- Joist span (2×8 at 16″ o.c.): 10′ vs. table maximum 11′ 10″ — within the table
- Beam span between posts (2-ply 2×10): 8′ vs. table maximum 8′ — within the table
Source: City of Alexandria, VA — Typical Deck Details, Based on International Residential Code (Tables 1 and 2). Basis: Southern pine No. 2, 40 psf live load + 10 psf dead load, wet service, deflection L/360. Other species and grades span less; snow loads, hot tubs and planters need engineering. Spans are measured between bearing centrelines.
Lumber to buy
| Item | Size | Length | Net | Buy |
|---|---|---|---|---|
| Joists | 2×8 | 10′ | 9 | 10 |
| Rim joists | 2×8 | 10′ | 1 | 1 |
| Ledger | 2×8 | 10′ | 1 | 1 |
| Beam plies | 2×10 | 10′ | 2 | 2 |
| Blocking | 2×8 | 8′ | 2 | 2 |
| Posts | 6×6 | 8′ | 1 | 1 |
| Deck boards | deck board | 20′ | 11 | 12 |
Hardware & fasteners
| Joist hangers (at ledger) | 9 |
| Hurricane ties / joist-to-beam connectors | 9 |
| Post bases (one per post) | 2 |
| Footings | 2 |
| Deck screws (2 per board per joist) | 416 |
| or hidden fastener clips (1 per board per joist) | 208 |
Screw count: 2 per board at every joist plus 2 at each butt joint, +5%. Ledger fastening, footing size and post bases come from your local code. Posts: 18 1/2″ above the footing to the underside of the beam (deck height minus decking, joist and beam depth).
Deck boards by length
| Board length | Boards | Total length |
|---|---|---|
| 8′ | 44 | 352 ft |
| 10′ | 22 | 220 ft |
| 12′ | 22 | 264 ft |
| 14′ | 22 | 308 ft |
| 16′ | 22 | 352 ft |
| 18′ | 22 | 396 ft |
| 20′ · least material | 11 | 220 ft |
22 rows of 5/4×6 wood (5 1/2″) with a 3/16″ gap cover 10′. Without waste. Stagger butt joints and land every joint on a joist.
Planning estimate only. Joist, beam, post, footing, ledger and guard requirements depend on loads, species, grade and your local building code. Verify with your building department or a licensed professional before you buy or build.
Boards by length
| Board length | 5 1/2″ boards (22 rows) | 3 1/2″ boards (33 rows) |
|---|---|---|
| 8′ | 44 | 66 |
| 10′ | 22 | 33 |
| 12′ | 22 | 33 |
| 14′ | 22 | 33 |
| 16′ | 22 | 33 |
| 18′ | 22 | 33 |
| 20′ · least waste | 11 | 17 |
Boards run along the 10 ft side, across joists 16″ on center. Rows = (120 + 3/16) ÷ (5 1/2 + 3/16) = 21.13 → 22.
Fasteners and framing
- Deck screws: 416 (2 per board per joist, +5%) — about 4.0 per sq ft.
- Hidden clips: about 208.
- Joists: 9 at 16″ on center, 117″ long for an attached deck (ledger + rim).
Joist size depends on span, species and spacing — see the span reference or plan the framing in the deck calculator. Other sizes: 8x8, 8x10, 10x12, 12x12, 12x16, 16x16, 10x20.
Planning estimates only. Stud counts and lumber lists are for budgeting and ordering. Structural sizes — headers, joists, beams, posts, footings, ledgers and guards — must follow your local building code. Verify with your building department or a licensed professional before you build.
FAQ
How many deck boards for a 10×10 deck?
11 boards of 20′ (12 with 10% waste) with 5 1/2″ boards and 3/16″ gaps: 22 rows across 10 ft, boards running the 10 ft way.
How many screws for a 10×10 deck?
About 416 deck screws at 16″ joist spacing: 2 per board at each of 9 joists, plus 5%. Hidden fasteners: about 208 clips.
How many joists for a 10×10 deck?
9 joists at 16″ on center across 10 ft (11 at 12″, 6 at 24″). Joist size depends on span — see the span table in the deck joist guide.